Olympia Chimney Flue Liner Replacement Nationwide

Olympia Chimney Flue Liner Replacement: The Plano Owner’s Guide

We stock and install Olympia Chimney-compatible flue liner replacement in Plano, with typical installed pricing running $2,800-$4,500 depending on liner diameter, height, and whether the existing clay tiles need extraction. Most Olympia Chimney liner jobs we book in Collin County are completed in a single day once the NFPA 211 Level 2 camera inspection confirms the scope. Homeowners usually discover the problem during a routine sweep when the camera catches a cracked tile, a gap at the mortar joint, or stainless showing pinholes at the waterline - or they notice water staining on the firebox wall after a hard North Texas rain.

Call (469) 240-3101

Which Olympia Chimney Models This Applies To

Olympia Chimney manufactures round and oval stainless steel liners in 304 and 316 alloys, with the 316Ti series being what we see most often in Plano homes built between 1995 and 2015. The critical compatibility gotcha is diameter-to-flue ratio: Olympia’s 6-inch liner is rated for appliances up to 120,000 BTU, but we’ve found Plano tract homes from the 2000s where the original mason left a 7×7 inch flue serving a 90,000 BTU furnace - too tight for safe venting, and the wrong Olympia spec sheet won’t catch it. We verify with a laser measure at the thimble and again at the crown before ordering.

Identification starts at the cleanout door or top termination. Olympia stamps the alloy grade and gauge on a tag near the collar; if the tag’s corroded off, we pull a 12-inch sample section and match wall thickness against the catalog. For OEM versus aftermarket, Olympia’s own 316Ti carries a lifetime warranty when installed with their proprietary connector kit, but we’ve had excellent results with HeatShield-compatible equivalents sourced through our Haven buying network at roughly 15% lower material cost. The decision comes down to whether your existing top plate and termination cap are Olympia-proprietary or universal-fit. Corrine Halstead will walk you through the match on the camera feed before anything gets ordered.

Signs Your Olympia Chimney Flue Liner Replacement Is Failing

• Water staining or rust streaks below the damper. Olympia’s 304 alloy liners in Plano’s clay soil environment tend to corrode at the condensation line where flue gases cool below dew point. The camera shows orange scaling at the smoke chamber shoulder - that’s metal loss, not surface discoloration.
• Bits of clay tile in the firebox or cleanout. When the original terracotta liner spalls from thermal cycling, fragments fall past a failing stainless overlay. We document the debris class during inspection; mixed tile and metal flakes mean both systems are compromised.
• Smoke rollout on startup or a persistent kerosene odor. A breached Olympia liner can allow flue gases to leak into the chimney cavity before the draft establishes. In Plano’s tight new construction, that smell often migrates through shared wall cavities before the CO detector ever trips.
• White efflorescence on the exterior brick below the roofline. This is moisture escaping through a liner gap, carrying dissolved salts from the mortar bed. It means flue gases and condensate have been washing the masonry from inside for at least one heating season, sometimes longer.
• The camera reveals a separated joint or “hanging” liner section. Olympia’s corrugated design allows some flex, but if the top termination has shifted or the support plate has corroded, a lower section can drop and create a gap that bypasses the flue entirely. We’ve seen this on three Plano homes near Legacy West after foundation movement from our expansive black gumbo clay.

Before

After

Replacement Cost & What’s Included

What drives the range: liner diameter and alloy gauge, whether we extract existing clay tiles or slip-line inside them, and accessibility from roof pitch or interior chase. Every Plano job we quote includes the NFPA 211 Level 2 camera inspection, written scope with line-item pricing, the documented photo record under Haven Standard Clause 4, and our 365-Day Done Right Promise. We source Olympia Chimney materials through our Haven buying network alongside DuraFlex, HeatShield, and Gelco - not to mix and match on a single job, but to keep customer prices honest through supplier competition.

DIY or Call Us?

There’s exactly one safe homeowner check: shine a flashlight up the flue from the firebox and look for visible gaps, light coming through cracks, or debris you didn’t put there. Do not attempt to measure, probe, or extract anything. Flue liner replacement involves working at height on a steep roof, handling sharp stainless edges, and sealing combustion-gas joints to NFPA 211 standards - a mistake means carbon monoxide in your living space or a chimney fire you won’t know about until the neighbor smells smoke.

We carry Olympia Chimney-compatible liner sections, connector kits, and termination hardware on our Plano service trucks, but we won’t sell parts for owner installation. The camera doesn’t guess. Neither do we. Call (469) 240-3101 and we’ll book the inspection, show you exactly what failed, and deliver a written price before any work starts.

FAQs